ARCHITECTURAL AND ENGINEERING SPECIFICATIONS TOWER MOUNTED GRAPHIC DISPLAY ANNUNCIATOR General This section describes the graphic display annunciator to be integrated as part of the total electrified fence security system. In particular, the graphic display will be used to annunciate electrified fence alarm and trouble conditions. The graphic display annunciator shall be suitable for rack mounting. The annunciator shall be provided to fit and mount within standard 19-inch EIA mounting standards. Materials The annunciator faceplate shall consist of a .1250-inch 6061-Ti aluminum substrate with a .020 inch poly carbonate graphic display bonded to the aluminum surface. All lamps and other annunciator equipment shall be mounted to the aluminum substrate. The graphic representation of the protected area shall be photographically produced on the reverse (back) side of the polycarbonate sheet. The outside (front) surface of the polycarbonate sheet shall have a non-glare velvet texture surface. The polycarbonate shall be one piece with no holes or penetrations. The graphic presentation shall be provided in one or more of 11 distinct colors as shown on the project plan and details. For example, a typical display will show the fence line and buildings in bright blue; alarm areas and zones in white; and zone nomenclature and wording in red. The faceplate and substrate graphics shall be accurately produced from a single computer-aided-design drawing assuring that the graphic surface will be accurately registered with the aluminum substrate containing the lamps. The polycarbonate sheet shall be bonded to the aluminum substrate using a nonhardening pressure sensitive adhesive. Annunciator lamps shall be multi-element ultrabrite light emitting diodes, Hewlett Packard HL Series, or equal. Each lamp shall be individually attached to the aluminum substrate. The front surface of each lamp shall be in direct contact with the polycarbonate graphic panel providing a 160-degree viewing angle. The graphic shall have a clear area over each lamp that is 25% larger than the lamp front surface. Each lamp shall be easily replaceable from the rear of the panel. Lamp colors shall be red for alarm; green for normal; and yellow for trouble. Lamp locations shall be as shown on the drawings. When there are long alarm zones there shall be a red alarm lamp approximately every 1 inch along the lenght of the zone. The graphic panel shall contain an illuminated legend. The legend shall consist of one each of the types of lamps used in the display. The illumination of the legend lamps shall be adjusted so the brightness is the same as any other active lamp on the display. The legend area shall be bordered and be headed by the word "LEGEND." Each lamp shall be labeled with its function. All connections to the graphic panel shall be via screw-type terminals. Each terminal shall be labeled with the function of the lamp connected to that terminal. A drawing of the graphic wiring connections shall be contained within the panel enclosure. For the cases in which the annunciator is used with a PLC map display driver module, the back of the aluminum substrate shall be drilled and tapped to accept up to two display driver modules. Wiring shall terminate directly to the display driver modules. The graphic display annunciator shall be a standard product of an established manufacturer. The annunciator shall be the EMPACT RM Series, or equal. FabricatIon Prior to manufacture, the graphic display artwork shall be generated in full scale and provided to the architect or owner for approval. The artwork shall be accurate in every detail including line-widths and lettering fonts. Provide the artwork in suflicient time to allow the architect or owner a minimum of two weeks for review without aftecting project schedule. If changes are requested, new full scale artwork incorporating the changes shall be resubmitted for approval. No production shall begin until graphic display artwork is approved. All wiring shall be a minimum 22-gauge with 300-volt color-coded vinyl insulation. Wiring shall be color coded to facilitate future service. Connections shall be either screw terminal or solder where appropriate. All equipment and wiring shall be factory installed in a neat, systematic manner using established wire-harnessing techniques. The wiring harness shall be laced or ty-wrapped at approximate 2-3 inch intervals. The completed graphic display annunciator shall be completely factory tested before shipment to the jobsite. Test documentation and quality control information shall be included with the annunciator. Patrol Vehicle Graphic Displays The shall be a quantity of ___ visor installed facility graphic maps showng the vehicle operator the location of all major buildings and alarm zones. Each patrol vehicle display shall: 1. Utilize the same substrate and graphic overlay construction as the tower mounted graphic display. 2. Provide a black matte finish for background and white text and lines. 3. Provide two cvisor clips on the reatr of each panel for visor mounting. 4. The display size shall be 5 inches be 9 inches. 2 2 2